<nobr id="eaybm"></nobr>

    1. <track id="eaybm"><span id="eaybm"><em id="eaybm"></em></span></track>
      <bdo id="eaybm"><optgroup id="eaybm"><dd id="eaybm"></dd></optgroup></bdo>
      <nobr id="eaybm"><address id="eaybm"></address></nobr>

    2. <bdo id="eaybm"></bdo>

          <menuitem id="eaybm"></menuitem>

            蘇機智能裝備

            歡迎來到蘇機智能裝備江蘇有限公司官方網站!

            咨詢熱線 consulting hotline:

            159-2175-1044 187-6132-4568

            - Suji Itelligent Equipment -
            線切割機床的維護常識Maintenance knowledge of wire cutting machine tools
            2023-6-7
            來源:未知
            點擊數:  681        作者:未知
            •      線切割機床不適合在污濁和高溫潮濕的環境中工作,電網供電環境也有較高的要求,機床供電電壓不應劣于±10%,三相應平衡穩定。線切割機床過于惡劣的電網必須加裝穩壓源。線切割機床機床除正常的保持整潔和潤滑以外,還必須用心維護如下幾個部位:
                   線切割機床機床的導軌和絲杠,絕不能沾染臟水和污物,一旦沾有臟物,要用干凈棉紗揩擦干凈后再用脫脂棉浸10#機油輕擦涂一遍。
                   線切割機床導輪和軸承,為導輪和軸承的壽命,也應把過于污濁的冷卻液換掉,如短時間不開機床,要無水讓導輪轉幾十秒鐘,將粧物甩出,卸下導輪座螺塞,注入潤滑脂,使污物通過油隙排出,以使導輪和軸承常處于較潔凈的狀態。
                  線切割機床絲筒軸和電機上的聯軸器和鍵,要使該部位始終處于嚴密穩妥的配合狀態,一旦出現鍵的松動和聯軸器的撞擊聲,要立即更換聯軸器的緩沖墊和鍵。長時間帶間隙的換向后,會使軸上的鍵槽變形張大。
                  線切割機床 控制柜與機床間的聯機電纜,拖地部分要有蓋板或塑料板保護,不可隨意踩踏,電纜要處于松弛自由狀態,不可以外力拉拽,不可使電纜插頭受力,不可將電纜波紋護套壓裂踩扁。
                  線切割機床控制臺(柜)搬動時要輕拿輕放,油污的手不要插拔觸摸接插件或鍵盤。
                  線切割機床 床面上的任何部位均不得敲砸或碰撞,特別是不可因超行程運動使絲架與床面干涉,那將嚴重損毀機床零件或精度。

                  要經常注意使導電塊處于良好的導電和與床身間的絕緣狀態,工作臺上墊條必須與床身絕緣,步進電機的拖線要處于自如狀態,步進電機確保無臟水入浸。

              Wire cutting machine tools are not suitable for working in dirty, high-temperature, and humid environments, and there are also high requirements for grid power supply environments. The power supply voltage of the machine tool should not be inferior to ± 10%, and the three-phase should be balanced and stable. The power grid of wire cutting machine tools that are too harsh must be equipped with a voltage stabilizing source. In addition to maintaining cleanliness and lubrication normally, wire cutting machine tools must also carefully maintain the following parts:
              The guide rails and screws of wire cutting machine tools must not be contaminated with dirt or water. Once dirt is found, it should be wiped clean with a clean cotton yarn and then lightly wiped with 10 # engine oil soaked in degreased cotton.
              For the service life of the guide rollers and bearings of wire cutting machine tools, excessively dirty coolant should also be replaced. If the machine tool is not turned on for a short period of time, it is necessary to let the guide rollers rotate without water for several tens of seconds, throw out the makeup, remove the screw plug of the guide roller seat, inject lubricating grease, and allow the dirt to be discharged through the oil gap to keep the guide rollers and bearings in a relatively clean state.
              The coupling and key on the wire cylinder shaft and motor of the wire cutting machine tool should always be in a tight and secure fit. Once the key loosens and the coupling makes a knocking sound, the buffer pad and key of the coupling should be replaced immediately. After a long period of reversing with gaps, the keyway on the shaft will become deformed and stretched.
              The online cable between the control cabinet of the wire cutting machine tool and the machine tool should be protected by a cover plate or plastic plate on the ground, and should not be stepped on casually. The cable should be in a loose and free state, and should not be pulled by external forces. The cable plug should not be subjected to force, and the corrugated sheath of the cable should not be crushed or flattened.
              When moving the control console (cabinet) of the wire cutting machine tool, it should be handled gently, and oily hands should not be inserted or pulled to touch the connector or keyboard.
              No part on the bed surface of the wire cutting machine tool should be knocked or collided, especially if the wire frame interferes with the bed surface due to overtravel movement, which will seriously damage the machine tool parts or accuracy.
              It is important to regularly ensure that the conductive block is in good conductivity and insulated from the bed. The padding on the workbench must be insulated from the bed, and the traction wire of the stepper motor should be in a free state. The stepper motor should ensure that there is no dirt or water entering.

            新聞資訊
            NEWS INFORMATION
            導  航:
            產品分類:
            新聞分類:
            聯系我們:

            蘇機智能裝備江蘇有限公司

            咨詢熱線:159-2175-1044 /18761324568

            公司傳真:0527-88655776
            公司郵箱:sujizhineng@163.com
            公司地址:宿遷市沭陽縣賜富路南、205國道東半固態產業園廠房
            郵編:223800
            Copyright © 2023-2024,www.www.ceceliajacksonphotography.net,All rights reserved ICP備案號:蘇ICP備20046852號-1
            亚洲人成网站999久久久综合|91香蕉国产线在线观看免费|五月丁香六月激情综合久久|日韩精品另类天天更新
            <nobr id="eaybm"></nobr>

              1. <track id="eaybm"><span id="eaybm"><em id="eaybm"></em></span></track>
                <bdo id="eaybm"><optgroup id="eaybm"><dd id="eaybm"></dd></optgroup></bdo>
                <nobr id="eaybm"><address id="eaybm"></address></nobr>

              2. <bdo id="eaybm"></bdo>

                    <menuitem id="eaybm"></menuitem>